Sharing NCDA certification NS0-158 dumps

Network Appliance NS0-158 exam is an important part of Network Appliance certification and Passcert has the latest Sharing NCDA certification NS0-158 dumps to prepare you for this test.Passcert Sharing NCDA certification NS0-158 dumps provides you an easy online solution to your Network Appliance NS0-158 exam Preparation. With Passcert Sharing NCDA certification NS0-158 dumps,you will find it easy to pass your NS0-158 exam.Passcert guarantees that you will be easily able to succeed in your NS0-158 Certification Exam.
Share some Network Appliance NCDA Certification NS0-158 exam questions and answers below.
You change the volume junction-path of vol1 from /vol/vol1 to /vol1. NFS clients are unable to connect to the new path/vol1. 
Which mirrors need to be updated to solve this problem? 
A. TDP mirrors of the SVM root volume. 
B. XDP mirrors of the SVM root volume 
C. DP mirrors of the SVM root volume 
D. LS mirrors of the SVM root volume 
Answer: D

Which data protocol is available to use on an SVM? 
A. FTP 
B. CIFS 
C. HTTP 
D. TFTP 
Answer: B 


The cluster ha modify-configured true command will trigger which two actions? (Choose two.) 
A. The ability for the nodes in an HA pair to execute an auto-giveback. 
B. The ability for the hosts connected to a node to failover to another HA pair. 
C. The storage can failover from one node to the other. 
D. SVM failover from any node in the cluster to any other node. 
Answer: B,C

You acquired a new company that has the same private IP address range. 
What must be set up on the NetApp cluster to support the duplicate networks? 
A. VLANs 
B. failover groups 
C. IPspaces 
D. DNS zone 
Answer: C

A customer has LUNs that are being accessed through iSCSI. The applications have experienced increased LUN latency over the last couple of days. 
Which two components should you review to determine what caused the rise in latency? (Choose two.) 
A. node CPU utilization 
B. FC switch performance 
C. Ethernet network performance 
D. cluster management switch performance 
Answer: A,C

What is the speed of the cluster interconnect ports on a FAS2552? 
A. 10 Gb 
B. 1 Gb 
C. 8 Gb 
D. 16 Gb 
Answer: A

Which type of connectivity is supported when connecting third-party arrays through FlexArray Virtualization for back-end storage to a NetApp cluster? 
A. iSCSI 
B. SAS 
C. FC 
D. Infiniband 
Answer: C

A customer enables Storage Efficiency on a volume, intending to use compression only as data is written. The customer observes that compression is working, but deduplication processes are still running on a scheduled basis. The customer wants to use compression without deduplication as the data is written to the volume. 
Which action will accomplish this task? 
A. Enable post compression on the volume. 
B. Create a custom efficiency policy and attach to the SVM. 
C. Attach the default efficiency policy to the volume. 
D. Attach the inline-only efficiency policy to the volume. 
Answer: D

Which command would you use to disable an account in clustered Data ONTAP? 
A. security login lock 
B. security login policy 
C. security login domain-tunnel 
D. security login modify 
Answer: A 


A customer created a volume with the wrong language code. 
What should a customer do to correct this problem? 
A. Delete the volume and create a volume with the correct language code. 
B. Take the volume offline and change the language code. 
C. Change the language code on the volume. 
D. Change the language code on the parent storage virtual machine. 
Answer: A

What are the two valid settings for fractional reserve? (Choose two.) 
A. 100% 
B. 20% 
C. 0% 
D. 50% 
Answer: A,C 


When assigning shelf IDs to SAS-connected shelves, which statement is true? 
A. They only need to be unique within an HA pair. 
B. They only need to be unique within a stack. 
C. They only need to be unique within a node. 
D. They need to be unique within a cluster. 
Answer: A 


A customer cannot enable storage failover. You have verified that the cabling is correct, the HA partners can communicate with each other, and cluster HA is configured. 
What must you do to resolve the problem? 
A. Set the HA state in the maintenance boot menu. 
B. Select option 4 in the boot menu. 
C. Set switchless cluster in privilege advanced mode. 
D. Modify epsilon in privilege advanced mode. 
Answer: D

Which of the following is true about a data protection (DP) mirror destination volume? (Choose all that apply) 
A. Can be in the same vserver as the source 
B. Can be in a different vserver as the source 
C. Can be on a different cluster from the source 
D. Can be on a Data ONTAP 7-mode system 
E. Can be smaller than the source 
Answer: A,B,C

Which two backup engines are supported within clustered Data ONTAP? (Choose two.) 
A. SMT ape 
B. dump 
C. tape 
D. xcopy 
Answer: A,B 


Clustered Data ONTAP supports which three versions of NFS? (Choose three.) 
A. NFSv4.1 
B. NFSv4 
C. NFSv3 
D. NFSv2 
E. NFSv1 
Answer: A,B,C

A customer wants to use jumbo frames on an interface group called a0a. Interface group a0a contains ports e0c and e0d. Additionally, the customer is using VLAN tagging for VLANs 510 and 520. VLAN 510 will use jumbo frames but VLAN 520 will not. When the customer tries to enable jumbo frames on a0a-510 the command fails. 
What caused the failure? 
A. The MTU size must be set on the broadcast domain to which the ports belong. 
B. The LIF corresponding with VLAN 510 is not configured for jumbo frames. 
C. Ports e0c and e0d have conflicting MTU sizes configured. 
D. Jumbo frames must be enabled from the advanced privilege set. 
Answer: A

A customer creates four broadcast domains with the following ports included for node cl-01: 
bcast1 ¨C e0c 
bcast2 ¨C e0d 
bcast3 ¨C e0e 
bcast4 ¨C e0f 
A customer creates a LIF and specifies a home port of cl-01:e0f. After LIF creation, the administrator modifies the home port to use cl-01:e0c. 
Which broadcast domain is the LIF using now? 
A. bcast4 
B. bcast2 
C. bcast1 
D. bcast3 
Answer: C

You notice your indirect I/O performance between nodes in your 4-node cluster is slowing down from prior week. Each node has two 10 GB connections to the cluster interconnect, one to each switch. You are using four out of 12 available ports on each cluster interconnect switch. Your cluster network utilization is over 80%. 
What should you do to increase cluster interconnect performance? 
A. Change the SFP+ from 10 Gb to 16 Gb on each node and switch. 
B. Add two more cluster interconnect connections per node. 
C. Add additional ISLs between the two cluster interconnect switches. 
D. Change the cable from TwinAx to optical with SFP+ for better throughput. 
Answer: B

Which port is used for untagged VLAN traffic? 
A. a0a-0 
B. a0a 
C. e0a-999 
D. 0a 
Answer: B 

From Passcert, you would get the latest Sharing NCDA certification NS0-158 dumps which are developed by our highly certified experts team according to the latest Network Appliance NS0-158 information. Don't hesitate to download the Sharing NCDA certification NS0-158 dumps and begin to prepare your exam right now. You can be successful! Be confident if you have our Sharing NCDA certification NS0-158 dumps. You are the No.1! On one hand, Passcert Sharing NCDA certification NS0-158 dumps helps you acquire the certification, on the other hand, it gives you the capacity to absorb the Network Appliance technology fully and very well.

Sharing NCIE-SAN Certification NS0-507 dumps

Passcert is a very good website for Sharing NCIE-SAN Certification NS0-507 dumps to provide convenience. According to the research of the past exam exercises and answers, Passcert can effectively capture the content of Network Appliance certification NS0-507 exam. Passcert Network Appliance NS0-507 exam exercises have a very close similarity with real examination exercises.
Share some Network Appliance NCIE-SAN NS0-507 exam questions and answers below.
Where do you identify the disk shelves and disks that are supported for a specific controller model? 
A. Hardware Universe (HWU) 
B. Interoperability Matrix Tool (IMT) 
C. Disk and Aggregates Power guide 
D. Installation and Setup Instructions poster 
Answer: A

When a new LUN is allocated, which volume and LUN configuration will use the smallest amount of storage? 
A. Volume guarantee none, fractional reserve 0, space reservation disabled 
B. Volume guarantee none, fractional reserve 0, space reservation enabled 
C. Volume guarantee volume, fractional reserve 100, space reservation enabled 
D. Volume guarantee volume, fractional reserve 100, space reservation enabled 
Answer: A

Where do you identify the disk shelves and disks that are supported for a specific controller model? 
A. Hardware Universe (HWU) 
B. Interoperability Matrix Tool (IMT) 
C. Disk and Aggregates Power guide 
D. Installation and Setup Instructions poster 
Answer: A

According to NetApp best practices, which method should be used for zoning? 
A. Single initiator ¨C multiple targets 
B. Multiple initiator ¨C single target 
C. Single initiator ¨C single target 
D. Multiple initiator ¨C multiple targets 
Answer: C

Within the NetApp Interoperability Matrix Tool (IMT), which three components are supported for the FC SAN storage host solution? (Choose three.) 
A. Host OS 
B. IP switch 
C. ONTAP OS 
D. Netapp Controller Model 
E. Host HBA 
Answer: A,C,E

You are planning a migration from a 7-mode system running Data ONTAP 7.3 to a new AFF A700 ONTAP 9.1 system. This 7-mode system provides only FC LUNs for a Windows Server 2012R2 server farm. The 7-Mode system cannot upgrade its volumes to 64-bit. 
In this scenario, what would you use for the migration? 
A. 7-Mode Transition Tool (7MTT) 
B. Foreign LUN Import (FLI) 
C. OnCommand System Manager 
D. Unified Host Utility Kit 
Answer: B

Within the NetApp Interoperability Matrix Tool (IMT), which three components are supported for the FC SAN storage host solution? (Choose three.) 
A. Host OS 
B. IP switch 
C. ONTAP OS 
D. Netapp Controller Model 
E. Host HBA 
Answer: A,C,E

You have an iSCSI host that is unable to connect to an SVM that is named “svm1” over a LIF that is named “lif1”. The home node and port of lif1 is cl01-01 port e0e. The event log show command displays the error iSCSI: network interface disabled for use; incoming connection discarded.Which command would you use to solve the problem? 
A. Broadcast-domain add-ports –broadcast-domain iscsi –ports cl01-01: e0e 
B. iSCSI interface enable –vserver svm1–lif lif1 
C. Network interface modify –vserver svm1 –lif lif1 –failover-group default 
D. Vserver iscsi create –target-alias svm1 –status-admin up –vserver svm1 
Answer: B

You need to take a cluster node down for extended maintenance, but you want to the FC LIF to avoid re-zoning the switch fabric. 
In this scenario, which three steps are required to move the FC LIF so it is available on another node? (Choose three.) 
A. Use the network interface migrate command to migrate the new home node and the new home port 
B. Perform a takeover and giveback operation for the new destination node 
C. Use the network interface modify command to modify the new home node and the new home port 
D. Bring the LIF online 
E. Take the LIF offline 
Answer: C,D,E

For which two vendor products would the Unified Host Utilities Kit set HBA and CAN parameters? (Choose two.) 
A. Brocade 
B. Cisco 
C. Emulex 
D. Qlogic 
Answer: C,D

You are asked to create a volume and lun, both of which need to be thin provisioned.In this scenario, which two statements are correct? (Choose two.) 
A. Use the lun create command with the space-reserve parameter set to disabled 
B. Use the lun create command with the space-reserve parameter set to enabled 
C. Use the volume create command with the space-guarantee parameter set to none 
D. Use the volume create command with the space-guarantee parameter set to volume 
Answer: A,C

According to NetApp best practices, which method should be used for zoning? 
A. Single initiator – multiple targets 
B. Multiple initiator – single target 
C. Single initiator – single target 
D. Multiple initiator – multiple targets 
Answer: C

You have expanded your ONTAP cluster from two nodes to four nodes and want to allow Linux multipathing software to see the paths to all nodes in the cluster. 
In this scenario, which statement describes how to accomplish this task? 
A. Add the WWPN to the host igroup then rescan from the host. 
B. Rescan from the host OS and modify the reporting nodes to add the two new nodes. 
C. Modify the reporting nodes to add the two new nodes the rescan from the host OS. 
D. Rescan from the host OS then add the WWPN to the host igroup. 
Answer: C

You are planning a migration from a 7-mode system running Data ONTAP 7.3 to a new AFF A700 ONTAP 9.1 system. This 7-mode system provides only FC LUNs for a Windows Server 2012R2 server farm. The 7-Mode system cannot upgrade its volumes to 64-bit.In this scenario, what would you use for the migration? 
A. 7-Mode Transition Tool (7MTT) 
B. Foreign LUN Import (FLI) 
C. OnCommand System Manager 
D. Unified Host Utility Kit 
Answer: B

You have expanded your ONTAP cluster from two nodes to four nodes and want to allow Linux multipathing software to see the paths to all nodes in the cluster.In this scenario, which statement describes how to accomplish this task? 
A. Add the WWPN to the host igroup then rescan from the host. 
B. Rescan from the host OS and modify the reporting nodes to add the two new nodes. 
C. Modify the reporting nodes to add the two new nodes the rescan from the host OS. 
D. Rescan from the host OS then add the WWPN to the host igroup. 
Answer: C

You have a switch called ¡°NK5-A¡±. The switch is configured with an NP_Port. 
Which switch feature on NK5-A uses NP_Ports to allow for fabric expansion of new FC switches without having to designate additional domain IDs? 
A. NPIV 
B. NPV 
C. FCIP 
D. F_port channel trunking 
Answer: D

You have an iSCSI host that is unable to connect to an SVM that is named ¡°svm1¡± over a LIF that is named ¡°lif1¡±. The home node and port of lif1 is cl01-01 port e0e. The event log show command displays the error iSCSI: network interface disabled for use; incoming connection discarded. 
Which command would you use to solve the problem? 
A. Broadcast-domain add-ports ¨Cbroadcast-domain iscsi ¨Cports cl01-01: e0e 
B. iSCSI interface enable ¨Cvserver svm1¨Clif lif1 
C. Network interface modify ¨Cvserver svm1 ¨Clif lif1 ¨Cfailover-group default 
D. Vserver iscsi create ¨Ctarget-alias svm1 ¨Cstatus-admin up ¨Cvserver svm1 
Answer: B

Where would you find the environment values of controllers and disk shelves (e.g. BTU and watts)? 
A. Interoperability matrix tool (IMT) 
B. Installation and setup instructions poster 
C. Config advisor 
D. Hardware universe 
Answer: D

Where would you find the environment values of controllers and disk shelves (e.g. BTU and watts)? 
A. Interoperability matrix tool (IMT) 
B. Installation and setup instructions poster 
C. Config advisor 
D. Hardware universe 
Answer: D

You need to perform a DR test on a FAS8200 with SAN LUNs using the onboard UTA2 with 16Gb SFP+. 
In this scenario, what is the minimum port speed required on the DR Site¡¯s FC switches? 
A. 2 Gb 
B. 16 Gb 
C. 8 Gb 
D. 4 Gb 
Answer: B

Besides, the Sharing NCIE-SAN Certification NS0-507 dumps have wide coverage of the content of the examination and the correct rate is up to 100%. Although there are many similar websites, perhaps they can provide you study guide and online services, our Passcert is leading these many websites. The reason of making the Passcert stand out in so many peers is that we have a lot of timely updated Sharing NCIE-SAN Certification NS0-507 dumps which accurately and correctly hit the exam.

McAFee SIEM certification MA0-104 free dumps

The McAFee SIEM certification MA0-104 free dumps contain the high quality questions and answers, its McAFee SIEM certification MA0-104 free dumps cover nearly 98% of the real exam and its simulated exams can make you feel that you are in the real examination room. The McAfee MA0-104 exam is the exam required to earn the MA0-104 Intel Security Certified Product Specialist certification. The MA0-104 exam is proof of a person's competence with the McAFee SIEM certification MA0-104 free dumps. Passcert guaranteed McAFee SIEM certification MA0-104 free dumps are comprehensive and helps you not only earn your certification in the shortest time possible, but to also gain the knowledge required on the job.
Share some McAfee Certified Product Specialist MA0-104 exam questions and answers below.
When viewing the Policy Tree, what four columns are displayed within the Rules Display pane? 
A. Action, Seventy, Aggregation, Copy Packet 
B. Action, Seventy, Normalization, Copy Packet 
C. Action, Seventy, Aggregation, Drop Packet 
D. Enable, Severity, Aggregation, Copy Packet 
Answer: A

If there is no firewall at the border of the network, which of the following could be used to simulate the protection a firewall provides? 
A. Load balancer 
B. Router Access Control List (ACL) 
C. Switch port blocking 
D. An email gateway 
Answer: B

Analysts can effectively use the McAfee SIEM to identify threats by ? 
A. focusing on aggregated and correlated events data. 
B. disabling aggregation, so all data are visible. 
C. studying ELM archives, to analyze the original data 
D. use the streaming event viewer to analyze data. 
Answer: A

Which of the following security technologies sits inline on the network and prevents attacks based on signatures and behavioral analysis that can be configured as a data source within the SIEM? 
A. Firewall 
B. Email Gateway 
C. Host Intrusion Prevention System 
D. Network Intrusion Prevention System 
Answer: D

An organization notices an increasing number of ESM concurrent connection events. To mitigate risks related to concurrent sessions which action should the organization take? 
A. Increase the concurrent session alarm threshold 
B. Decrease the console timeout value 
C. Increase the number of the concurrent sessions allowed 
D. Customize the login page with the organization's logo 
Answer: B

We all know that in the fiercely competitive IT industry, having some IT authentication certificates is very necessary. IT authentication certificate is a best proof for your IT professional knowledge and experience.Passcert not only have a high reliability, but also provide a good service. If you choose Passcert McAFee SIEM certification MA0-104 free dumps, but don't pass the exam, we will 100% refund full of your cost to you. Passcert also provide you with a free update service for one year.

Veritas NetBackup 8.0 VCS-276 free dumps

We are offering you detailed Veritas NetBackup 8.0 VCS-276 free dumps. Passcert experts come from different parts of the Industry and are most experienced and qualified to have the opportunity to write the Veritas NetBackup 8.0 VCS-276 free dumps. Our Passcert Veritas NetBackup 8.0 VCS-276 free dumps are even more difficult than the actual test.
Share some Veritas Certified Specialist (VCS) VCS-276 exam questions and answers below.
A backup image on tape is due to expire in one week. The administrator needs to keep the image available for restore indefinitely. 
Which two methods can be used to accomplish this goal? (Select two.) 
A. use the bpexpdate command to change the expiration date of the image 
B. use the bpretlevel command to customize the retention level 
C. use the bpimmedia command to freeze the tape 
D. use the bpduplicate command to create a copy with an infinite retention 
E. use the vmchange command to change the expiration date of the tape 
Answer: A, D

An administrator is attempting to configure a new backup policy using synthetic backups. When creating a new full backup schedule, the Synthetic backup option is unable to be selected. What must the administrator do to the policy to make the Synthetic backup option available for selection? 
A.create a differential or cumulative incremental backup schedule 
D.select a backup destination that supports synthetic backups 
C.enable Collect true image restore information with move detection 
D.create a full backup schedule with Accelerator forced rescan enabled 
Answer: A

What is the purpose of the Login and Password settings in the Disaster Recovery tab of a Net Backup catalog backup policy? 
A. to specify credentials required to access a network share 
B. to encrypt the Net Backup catalog backup data 
C. to require credentials to perform a catalog recovery 
D. to encrypt the disaster recovery file 
Answer: D

An administrator has a scheduled policy has a scheduled policy backs up 20 clients, each with multiple mount points and multiple data streams enabled. One of the jobs has failed and is in an Incomplete slate in the Activity Monitor. 
Mow should the administrator verify the incomplete job runs prior to the next scheduled backup? 
A. run a manual job the client 
B. resume the job 
C. run a manual job for the mount point 
D. resume the parent job 
Answer: B

Which configuration file should an administrator modify to enable local fingerprint caching on a Netbackup MSDP client? 
A. spa.cfg 
B. pd.conf 
C. contentrouter.cfg 
D. agent.cfg 
Answer: B

Which command can an administrator run to test and analyze connections between master servers, media servers, and clients for multiple Net Back up ports? 
A. bperror 
B. bpconfig 
C. bpresolver 
D. bptestnetconn 
Answer: D

How can an administrator copy an existing backup image of client1.example.com from an Advanced Disk storage unit to a Media Server Deduplication Pool (MSDP)? 
A. run bpimport with the source and the destination storage unit 
B. create a Storage Lifecycle Policy that contains a duplication to the MSDP pool 
C. run bpduplicate with the backup ID and the destination storage unit 
D. run nbreplicate with the backup ID and the destination storage unit 
Answer: D

An administrator has a job that has failed. See the contents of the Job's Detailed Status tab from the NetBackup Activity Monitor provided below: 



What may be the cause for the failure? 
A. The version of NetBackup installed on the master server and media server is higher than the version installed on the client. 
B. The media server is unable to resolve the hostname of the client to any IP address. 
C. The required NetBackup processes need to be started on the client. 
D. The media server failed to perform a reverse name lookup of the IP address associated with the client. 
Answer: A

Some NetBackup jobs are affected by the failure of a disk in an Advanced Disk pool, but the jobs are unavailable to view in the Activity Monitor. 
In which two places can the administrator view Net Backup jobs affected by the disk failure? (Select two.) 
A. Media and Device Management > Device Monitor > Disk Pool 
B. Net Backup Management > Reports > Disk Reports > Disk logs 
C. Net Backup Management > Reports > Disk Reports > Disk Pool Status 
D. Net Backup Management > Reports > Disk Reports > Disk Storage Unit Status 
E. Net Backup Management > Reports > Media Logs 
Answer: AD

Which action is performed by the NetBackup deduplication plug-in? 
A. writing data segments into the MSDP containers 
B. processing MSDP transaction logs 
C. performing file fingerprinting actions 
D. expiring images from the NetBackup catalog 
Answer: C

An administrator is preparing to perform disaster recovery for many clients whose backups are stored on multiplexed tapes. Which host property should the administrator modify, prior to the restores, to ensure the best recovery time? 
A.set Enable unrestricted media sharing for all media servers 
B.increase Restore retries 
C.increase Delay on multiplexed restores 
D.add the client IP addresses to Resilient Network 
Answer: A

Winch backup storage is unsupported with media server load balancing? 
A. BasicDisk 
B. Media Server Deduplication Pool 
C. AdvancedDisk 
D. Media Manager storage 
Answer: D

An administrator is preparing to perform disaster recovery for many clients whose backups are stored on multiplexed tapes. 
Which host property should the administrator modify, prior to the restores, to ensure the best recovery time? 
A. set Enable unrestricted media sharing for all media servers 
B. increase Restore retries 
C. increase Delay on multiplexed restores 
D. add the client IP addresses to Resilient Network 
Answer: A

An administrator has a backup policy with the following attributes: 



Allow multiple data streams is selected 
Max Jobs per Client value set to 4 
How many jobs go Active when the job is started, excluding parent jobs? 
A. 8 
B. 9 
C. 12 
D. 15 
Answer: C

Refer to the exhibit. 
A backup job configured with a retention level of 2 and Policy volume pool set to the server_tapes is failing due to Status Code 96: Unable to allocate media for backup. See the output of the available_media command below: 



Which task in the NetBackup Administration Console should the administrator perform to resolve the status code 96 error? 
A. Change volume C11201 to the scratch_pool volume pool 
B. Change volume E02002 to the scratch_pool volume pool 
C. Change volume E02004 to the scratch_pool volume pool 
D. Change volume E02003 to the scratch_pool volume pool 
Answer: C

Which two storage unit types can be configured in NetBackup? (Select two.) 
A. deduplication 
B. NDMP 
C. robot 
D. media manager 
E. tape 
Answer: B, D

An administrator configures a default Standard die system backup policy, which backs up very large file systems from a set of clients, There are multiple scheduled backup attempts configured. 
How can the administrator reduce the amount of time needed to complete these backup jobs alter failures? 
A. configure the Take checkpoints every policy setting 
B. increase the Job retry delay host property setting 
C. use the Resume Job action instead of Restart Job 
D. increase the Client connect timeout host property setting 
Answer: A

Which type of backup schedules ore available when using the After each backup session schedule type for an NBU-Catalog policy type? 
A. Full 
B. Differential Incremental 
C. Vault Catalog Backup 
D. Application Backup 
Answer: A

Backup images that reside In an MSDP storage pool have been manually expired using bpexpdate. Which step must fin administrator perform to manually free the associated space in the storage pool? 
A. run image cleanup on the media server that hosts the MSDP storage server 
B. run an inventory on the MSDP storage pool 
C. run content router queue processing on media server that hosts the MSDP storage server 
D. fun content router queue processing on the master server 
Answer: C

Weekly full backups run for client A on maeter1 using a storage unit that belongs to medial. The administrator is required to retain client A¡¯s full backups for a period of four months. When the administrator modifies the full schedule, an option for 4 months is missing from the Retention drop down list. 
How can the administrator add a four month retention? 
A. modify an existing retention level in the server host properties, under Retention Periods 
B. ignore the selection list and type in the desired retention period directly 
C. add a new retention period in the media server host properties, under Retention Periods 
D. increase the Image cleanup Interval in the master server host properties, under Clean-up 
Answer: D

Passcert is a website to provide IT certification exam training tool for people who attend IT certification exam examinee. Passcert Veritas NetBackup 8.0 VCS-276 free dumps has strong pertinence, which can help you save a lot of valuable time and energy to pass IT certification exam. Our Veritas NetBackup 8.0 VCS-276 free dumps and are very close true examination questions. IN a short time of using Passcert Veritas NetBackup 8.0 VCS-276 free dumps, you can 100% pass the exam. So spending a small amount of time and money in exchange for such a good result is worthful. Please add Passcert Veritas NetBackup 8.0 VCS-276 free dumps in your shopping cart now.